Volvo Vehicle Models Volvo XC40 2017-present
Volvo Vehicle Models Volvo XC40 2017-present Torque Specifications
Complete Volvo Vehicle Models Volvo XC40 2017-present torque specifications guide. Includes factory-specified torque values, torque sequences, and technical specifications for all components including body, brakes, drivetrain, electrical, emissions sensors, fuel, exhaust, HVAC, and suspension. Essential information for proper assembly and maintenance.
Updated
Important Information
Safety guidelines and reference information for proper torque application
Safety First
- Always verify torque specifications with your vehicle's factory service manual
- Use properly calibrated torque wrenches
- Replace all torque-to-yield (TTY) bolts - they are single-use only
- When in doubt, consult a professional mechanic
Quick Reference Guide
Quick Reference Guide
ft-lbs → Nm
× 1.356
ft-lbs → kg-m
× 0.138
Nm → ft-lbs
× 0.738
in-lbs → ft-lbs
× 0.083
Common Torque Patterns
Star Pattern
Used for wheels and other circular bolt patterns
Cross Pattern
Used for gaskets and cover plates
Sequential Pattern
Used for head bolts and other critical components
Common Mistakes to Avoid
Common Mistakes to Avoid
Over-tightening
Exceeding the specified torque value can stretch or break fasteners, damage threads, or crack components.
Prevention:
Always use a calibrated torque wrench and follow specifications exactly.
Incorrect Torque Sequence
Tightening bolts in the wrong order can cause uneven pressure distribution and potential leaks or damage.
Prevention:
Follow the manufacturer's specified torque sequence pattern.
Dirty Threads
Dirt, rust, or old thread locker can affect torque readings and proper fastener tension.
Prevention:
Clean and inspect all threads before assembly. Use new thread locker if specified.
Reusing TTY Bolts
Torque-to-yield bolts are designed to stretch and must not be reused.
Prevention:
Always replace TTY bolts with new ones. They are single-use only.
Dry vs. Lubricated
Not accounting for whether torque specs are for dry or lubricated fasteners can lead to incorrect tension.
Prevention:
Check if specs are for dry or lubricated threads. Use specified lubricant when required.
Recommended Tools
Recommended Tools
Torque Wrench (1/4" Drive)
Range: 2-25 ft-lbs
Small fasteners, delicate components
Torque Wrench (3/8" Drive)
Range: 10-100 ft-lbs
Most common automotive fasteners
Torque Wrench (1/2" Drive)
Range: 30-250 ft-lbs
Large fasteners, wheels
Angle Gauge
Torque-to-yield (TTY) bolts
Torque Wrench Care
- Calibrate annually or after 5,000 clicks
- Store at lowest setting
- Keep clean and lubricated
Search Specifications
Search by component name, bolt size, or description
Type to search through torque specifications. Use arrow keys to navigate results. Press Enter to select a result.
Torque Calculator
Convert between different torque units
2.0l Engine
Torque specifications for 2.0L Engine
2.0l Engine
Torque specifications for 2.0L Engine
Cylinder Head and Engine Block
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
27.5 ft-lbs (37.3 N·m)
Important Notes
Estimated value, consult manufacturer's recommendations for correct torque specification.
2 Main Bearing Bolts
M14 x 1.5
2
Main Bearing Bolts
M14 x 1.5
Torque Specification
57.5 ft-lbs (78 N·m)
Crankshaft and Connecting Rods
1 Connecting Rod Nuts
M10 x 1.5
1
Connecting Rod Nuts
M10 x 1.5
Torque Specification
32.5 ft-lbs (44 N·m)
2 Flywheel Bolts
M12 x 1.5
2
Flywheel Bolts
M12 x 1.5
Torque Specification
57.5 ft-lbs (78 N·m)
Valvetrain and Timing System
1 Camshaft Sprocket Bolt
M14 x 1.5
1
Camshaft Sprocket Bolt
M14 x 1.5
Torque Specification
57.5 ft-lbs (78 N·m)
2 Timing Belt/Chain Tensioner Bolt
M10 x 1.5
2
Timing Belt/Chain Tensioner Bolt
M10 x 1.5
Torque Specification
20 ft-lbs (27.1 N·m)
Engine Accessories
1 Water Pump Bolts
M10 x 1.5
1
Water Pump Bolts
M10 x 1.5
Torque Specification
17.5 ft-lbs (23.7 N·m)
2 Thermostat Housing Bolts
M8 x 1.25
2
Thermostat Housing Bolts
M8 x 1.25
Torque Specification
8 ft-lbs (10.8 N·m)
Intake and Exhaust System
1 Intake Manifold Bolts
M10 x 1.5
1
Intake Manifold Bolts
M10 x 1.5
Torque Specification
8 ft-lbs (10.8 N·m)
2 Exhaust Manifold/Headers Bolts
M12 x 1.5
2
Exhaust Manifold/Headers Bolts
M12 x 1.5
Torque Specification
27.5 ft-lbs (37.3 N·m)
Fuel System
1 Fuel Rail Bolts
M8 x 1.25
1
Fuel Rail Bolts
M8 x 1.25
Torque Specification
8 ft-lbs (10.8 N·m)
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (10.8 N·m)
Ignition System
1 Spark Plugs
M14 x 1.25
1
Spark Plugs
M14 x 1.25
Torque Specification
17.5 ft-lbs (23.7 N·m)
2 Ignition Coil Bolt
M8 x 1.25
2
Ignition Coil Bolt
M8 x 1.25
Torque Specification
8 ft-lbs (10.8 N·m)
Turbocharger System
1 Turbocharger Mounting Bolts
M12 x 1.5
1
Turbocharger Mounting Bolts
M12 x 1.5
Torque Specification
35 ft-lbs (47.4 N·m)
Important Notes
Estimated value, consult manufacturer's recommendations for correct torque specification.
2.0l I4 Engine
Torque specifications for 2.0L-I4 Engine
2.0l I4 Engine
Torque specifications for 2.0L-I4 Engine
Cylinder Head and Valvetrain
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
27.5 ft-lbs (37.3 N·m)
Important Notes
Estimated average of 25-30 ft-lbs range.
2 Rocker Arms/Shafts Bolts
M10 x 1.25
2
Rocker Arms/Shafts Bolts
M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated average of 18-22 ft-lbs range.
3 Valve Cover Bolts
M8 x 1.25
3
Valve Cover Bolts
M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated average of 7-9 ft-lbs range.
Engine Block and Crankshaft
1 Main Bearing Bolts
M14 x 1.5
1
Main Bearing Bolts
M14 x 1.5
Torque Specification
57.5 ft-lbs (78 N·m)
Important Notes
Estimated average of 55-60 ft-lbs range.
2 Connecting Rod Nuts
M12 x 1.5
2
Connecting Rod Nuts
M12 x 1.5
Torque Specification
32.5 ft-lbs (44 N·m)
Important Notes
Estimated average of 30-35 ft-lbs range.
3 Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
3
Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
Torque Specification
113.5 ft-lbs (153.8 N·m)
Important Notes
Estimated average of 111-116 ft-lbs range.
Timing and Accessory Components
1 Timing Belt/Chain Tensioner Bolt
M10 x 1.25
1
Timing Belt/Chain Tensioner Bolt
M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated average of 18-22 ft-lbs range.
2 Camshaft Sprocket Bolt
M14 x 1.5
2
Camshaft Sprocket Bolt
M14 x 1.5
Torque Specification
57.5 ft-lbs (78 N·m)
Important Notes
Estimated average of 55-60 ft-lbs range.
3 Water Pump Bolts
M10 x 1.25
3
Water Pump Bolts
M10 x 1.25
Torque Specification
17.5 ft-lbs (23.7 N·m)
Important Notes
Estimated average of 15-20 ft-lbs range.
Intake and Exhaust Components
1 Intake Manifold Bolts
M10 x 1.25
1
Intake Manifold Bolts
M10 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated average of 7-9 ft-lbs range.
2 Exhaust Manifold/Headers Bolts
M12 x 1.5
2
Exhaust Manifold/Headers Bolts
M12 x 1.5
Torque Specification
27.5 ft-lbs (37.3 N·m)
Important Notes
Estimated average of 25-30 ft-lbs range.
3 Throttle Body Bolts
M8 x 1.25
3
Throttle Body Bolts
M8 x 1.25
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated average of 7-9 ft-lbs range.
Engine Mounting and Accessory Components
1 Engine Mounting Bolts
M14 x 1.5
1
Engine Mounting Bolts
M14 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated average of 40-50 ft-lbs range.
2 Oil Pan Bolts
M10 x 1.25
2
Oil Pan Bolts
M10 x 1.25
Torque Specification
10 ft-lbs (13.6 N·m)
Important Notes
Estimated average of 9-11 ft-lbs range.
3 Oil Filter Housing Bolt
M10 x 1.25
3
Oil Filter Housing Bolt
M10 x 1.25
Torque Specification
17.5 ft-lbs (23.7 N·m)
Important Notes
Estimated average of 15-20 ft-lbs range.
2.0l I4 Turbo Engine
Torque specifications for 2.0L-I4-TURBO Engine
2.0l I4 Turbo Engine
Torque specifications for 2.0L-I4-TURBO Engine
Cylinder Head and Engine Block
1 Cylinder Head Bolts
M12 x 1.5
1
Cylinder Head Bolts
M12 x 1.5
Torque Specification
27.5 ft-lbs (37.3 N·m)
Important Notes
Estimated value, consult manufacturer's recommendations for correct torque specification.
2 Main Bearing Bolts
M14 x 1.5
2
Main Bearing Bolts
M14 x 1.5
Torque Specification
57.5 ft-lbs (78 N·m)
Crankshaft and Connecting Rods
1 Connecting Rod Nuts
M10 x 1.5
1
Connecting Rod Nuts
M10 x 1.5
Torque Specification
32.5 ft-lbs (44 N·m)
2 Flywheel Bolts
M12 x 1.5
2
Flywheel Bolts
M12 x 1.5
Torque Specification
57.5 ft-lbs (78 N·m)
Valvetrain and Timing System
1 Camshaft Sprocket Bolt
M14 x 1.5
1
Camshaft Sprocket Bolt
M14 x 1.5
Torque Specification
57.5 ft-lbs (78 N·m)
2 Timing Belt/Chain Tensioner Bolt
M10 x 1.5
2
Timing Belt/Chain Tensioner Bolt
M10 x 1.5
Torque Specification
20 ft-lbs (27.1 N·m)
Engine Accessories
1 Water Pump Bolts
M10 x 1.5
1
Water Pump Bolts
M10 x 1.5
Torque Specification
17.5 ft-lbs (23.7 N·m)
2 Thermostat Housing Bolts
M8 x 1.25
2
Thermostat Housing Bolts
M8 x 1.25
Torque Specification
8 ft-lbs (10.8 N·m)
Intake and Exhaust System
1 Intake Manifold Bolts
M10 x 1.5
1
Intake Manifold Bolts
M10 x 1.5
Torque Specification
8 ft-lbs (10.8 N·m)
2 Exhaust Manifold/Headers Bolts
M12 x 1.5
2
Exhaust Manifold/Headers Bolts
M12 x 1.5
Torque Specification
27.5 ft-lbs (37.3 N·m)
Fuel System
1 Fuel Rail Bolts
M8 x 1.25
1
Fuel Rail Bolts
M8 x 1.25
Torque Specification
8 ft-lbs (10.8 N·m)
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (10.8 N·m)
Ignition System
1 Spark Plugs
M14 x 1.25
1
Spark Plugs
M14 x 1.25
Torque Specification
17.5 ft-lbs (23.7 N·m)
2 Ignition Coil Bolt
M8 x 1.25
2
Ignition Coil Bolt
M8 x 1.25
Torque Specification
8 ft-lbs (10.8 N·m)
Turbocharger System
1 Turbocharger Mounting Bolts
M12 x 1.5
1
Turbocharger Mounting Bolts
M12 x 1.5
Torque Specification
35 ft-lbs (47.4 N·m)
Important Notes
Estimated value, consult manufacturer's recommendations for correct torque specification.
Body
Torque specifications for Body
Body
Torque specifications for Body
Suspension
1 Strut/Shock Absorber Mounting Bolts
M14 x 1.5
1
Strut/Shock Absorber Mounting Bolts
M14 x 1.5
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Torque value is an average of the recommended range.
2 Control Arm Bolts
M16 x 1.5
2
Control Arm Bolts
M16 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Torque value is an average of the recommended range.
3 Ball Joint Nut
M18 x 1.5
3
Ball Joint Nut
M18 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Torque value is an average of the recommended range.
Steering
1 Tie Rod End Nut
M12 x 1.25
1
Tie Rod End Nut
M12 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Torque value is an average of the recommended range.
2 Sway Bar Link Nut
M10 x 1.25
2
Sway Bar Link Nut
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Torque value is an average of the recommended range.
3 Steering Gear/Rack Bolts
M14 x 1.5
3
Steering Gear/Rack Bolts
M14 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Torque value is an average of the recommended range.
Body and Frame
1 Body Mount Bolts
M16 x 1.5
1
Body Mount Bolts
M16 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated torque value based on similar components.
2 Door Hinge Bolts
M10 x 1.25
2
Door Hinge Bolts
M10 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated torque value based on similar components.
3 Hood Hinge Bolts
M10 x 1.25
3
Hood Hinge Bolts
M10 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated torque value based on similar components.
4 Trunk Lid Hinge Bolts
M10 x 1.25
4
Trunk Lid Hinge Bolts
M10 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated torque value based on similar components.
5 Bumper Mounting Bolts
M12 x 1.25
5
Bumper Mounting Bolts
M12 x 1.25
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Estimated torque value based on similar components.
6 Fender Mounting Bolts
M10 x 1.25
6
Fender Mounting Bolts
M10 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated torque value based on similar components.
Brakes
Torque specifications for Brakes
Brakes
Torque specifications for Brakes
Brake Caliper and Mounting
1 Brake Caliper Bolts
M14 x 1.5
1
Brake Caliper Bolts
M14 x 1.5
Torque Specification
92.5 ft-lbs (125 N·m)
Important Notes
Torque value is an average of the specified range (85-100 ft-lbs).
2 Brake Caliper Mounting Bracket Bolts
M12 x 1.25
2
Brake Caliper Mounting Bracket Bolts
M12 x 1.25
Torque Specification
72.5 ft-lbs (98 N·m)
Important Notes
Torque value is an average of the specified range (65-80 ft-lbs).
Brake Disc/Drum and Rotor
1 Brake Disc/Drum Retaining Bolts
M10 x 1.25
1
Brake Disc/Drum Retaining Bolts
M10 x 1.25
Torque Specification
27.5 ft-lbs (37.5 N·m)
Important Notes
Torque value is an average of the specified range (25-30 ft-lbs).
2 Brake Rotor Bolts (if applicable)
M12 x 1.5
2
Brake Rotor Bolts (if applicable)
M12 x 1.5
Torque Specification
35 ft-lbs (47.5 N·m)
Important Notes
Torque value is an estimate based on general industry standards.
Wheel and Hub
1 Wheel Lug Nuts
M14 x 1.5
1
Wheel Lug Nuts
M14 x 1.5
Torque Specification
102.5 ft-lbs (139 N·m)
Important Notes
Torque value is an average of the specified range (95-110 ft-lbs).
Brake Master Cylinder and ABS Module
1 Brake Master Cylinder Mounting Bolts
M10 x 1.25
1
Brake Master Cylinder Mounting Bolts
M10 x 1.25
Torque Specification
17.5 ft-lbs (23.75 N·m)
Important Notes
Torque value is an estimate based on general industry standards.
2 ABS Module Mounting Bolts
M8 x 1.25
2
ABS Module Mounting Bolts
M8 x 1.25
Torque Specification
12.5 ft-lbs (17 N·m)
Important Notes
Torque value is an estimate based on general industry standards.
Brake Lines and Fittings
1 Brake Line Fittings
M8 x 1.25
1
Brake Line Fittings
M8 x 1.25
Torque Specification
12.5 ft-lbs (17 N·m)
Important Notes
Torque value is an estimate based on general industry standards.
Dct7 Transmission
Torque specifications for Dct7 Transmission
Dct7 Transmission
Torque specifications for Dct7 Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M12 x 1.5
1
Transmission Mounting Bolts
M12 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Torque value is an average of the recommended range.
Transmission Oil Pan
1 Transmission Oil Pan Bolts
M10 x 1.25
1
Transmission Oil Pan Bolts
M10 x 1.25
Torque Specification
10 ft-lbs (14 N·m)
Transmission Drain and Fill Plugs
1 Transmission Drain and Fill Plugs
M14 x 1.5
1
Transmission Drain and Fill Plugs
M14 x 1.5
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Torque value is an average of the recommended range.
Transmission Case and Gearbox
1 DCT7 Transmission Case Bolts
M14 x 1.5
1
DCT7 Transmission Case Bolts
M14 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Torque value is estimated based on industry standards.
2 DCT7 Transmission Gearbox Bolts
M16 x 1.5
2
DCT7 Transmission Gearbox Bolts
M16 x 1.5
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Torque value is estimated based on industry standards.
Transmission Clutch Pack and Solenoid
1 DCT7 Transmission Clutch Pack Bolts
M10 x 1.25
1
DCT7 Transmission Clutch Pack Bolts
M10 x 1.25
Torque Specification
22.5 ft-lbs (30.5 N·m)
Important Notes
Torque value is estimated based on industry standards.
2 DCT7 Transmission Solenoid Bolts
M8 x 1.25
2
DCT7 Transmission Solenoid Bolts
M8 x 1.25
Torque Specification
12.5 ft-lbs (17 N·m)
Important Notes
Torque value is estimated based on industry standards.
Drivetrain
Torque specifications for Drivetrain
Drivetrain
Torque specifications for Drivetrain
Engine and Transmission Mounting
1 Engine Block to Transmission Bellhousing Bolts
M14 x 1.5
1
Engine Block to Transmission Bellhousing Bolts
M14 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value based on general industry standards.
2 Transmission Crossmember Bolts
M14 x 1.5
2
Transmission Crossmember Bolts
M14 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value based on general industry standards.
Flywheel and Crankshaft
1 Flywheel Bolts
M12 x 1.5
1
Flywheel Bolts
M12 x 1.5
Torque Specification
57.5 ft-lbs (78 N·m)
Main Bearings and Connecting Rods
1 Main Bearing Bolts
M12 x 1.5
1
Main Bearing Bolts
M12 x 1.5
Torque Specification
57.5 ft-lbs (78 N·m)
2 Connecting Rod Nuts
M10 x 1.5
2
Connecting Rod Nuts
M10 x 1.5
Torque Specification
32.5 ft-lbs (44 N·m)
Camshaft and Valvetrain
1 Camshaft Sprocket Bolt
M12 x 1.5
1
Camshaft Sprocket Bolt
M12 x 1.5
Torque Specification
57.5 ft-lbs (78 N·m)
Crankshaft Pulley and Harmonic Balancer
1 Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
1
Crankshaft Pulley/Harmonic Balancer Bolt
M16 x 1.5
Torque Specification
113.5 ft-lbs (154 N·m)
Transmission and Drive Axle
1 Transmission Mounting Bolts
M14 x 1.5
1
Transmission Mounting Bolts
M14 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
2 Drive Axle/Half Shaft Bolts
M14 x 1.5
2
Drive Axle/Half Shaft Bolts
M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
CV Joint and Axle Nut
1 CV Joint/Axle Nut
M20 x 1.5
1
CV Joint/Axle Nut
M20 x 1.5
Torque Specification
190 ft-lbs (258 N·m)
Propeller/Drive Shaft
1 Propeller/Drive Shaft Bolts
M14 x 1.5
1
Propeller/Drive Shaft Bolts
M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Differential
1 Differential Drain/Fill Plug
M12 x 1.5
1
Differential Drain/Fill Plug
M12 x 1.5
Torque Specification
27.5 ft-lbs (37 N·m)
Electric Engine
Torque specifications for ELECTRIC Engine
Electric Engine
Torque specifications for ELECTRIC Engine
Engine Mounting and Accessories
1 Electric Motor Mounting Bolts
M14 x 1.5
1
Electric Motor Mounting Bolts
M14 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Estimated value based on similar components and bolt sizes.
2 Starter Motor Mounting Bolts
M10 x 1.25
2
Starter Motor Mounting Bolts
M10 x 1.25
Torque Specification
32 ft-lbs (44 N·m)
3 Alternator Mounting Bolts
M10 x 1.25
3
Alternator Mounting Bolts
M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
4 Inverter Mounting Bolts
M12 x 1.5
4
Inverter Mounting Bolts
M12 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Electrical System
1 Battery Terminal Nuts
M8 x 1.25
1
Battery Terminal Nuts
M8 x 1.25
Torque Specification
6 ft-lbs (8 N·m)
2 High-Voltage Cable Bolts
M6 x 1.0
2
High-Voltage Cable Bolts
M6 x 1.0
Torque Specification
12 ft-lbs (16 N·m)
3 Electric Engine Control Module (ECM) Mounting Bolts
M8 x 1.25
3
Electric Engine Control Module (ECM) Mounting Bolts
M8 x 1.25
Torque Specification
12 ft-lbs (16 N·m)
Cooling System
1 Electric Motor Cooling System Bolts
M10 x 1.25
1
Electric Motor Cooling System Bolts
M10 x 1.25
Torque Specification
17 ft-lbs (23 N·m)
Electrical
Torque specifications for Electrical
Electrical
Torque specifications for Electrical
Ignition System
1 Ignition Coil Bolt
M6 x 1.0
1
Ignition Coil Bolt
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure proper torque to avoid damage to the coil or spark plug.
Starting System
1 Starter Motor Mounting Bolt
M10 x 1.5
1
Starter Motor Mounting Bolt
M10 x 1.5
Torque Specification
32 ft-lbs (44 N·m)
Important Notes
Ensure proper alignment and electrical grounding.
Charging System
1 Alternator Mounting Bolt
M8 x 1.25
1
Alternator Mounting Bolt
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper alignment with the drive belt.
Battery System
1 Battery Terminal Nut
M6 x 1.0
1
Battery Terminal Nut
M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Ensure a reliable electrical connection to prevent overheating or arcing.
Ac System
1 A/C Compressor Mounting Bolt
M8 x 1.25
1
A/C Compressor Mounting Bolt
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure proper alignment with the drive belt.
2 A/C Line Fitting
M8 x 1.25
2
A/C Line Fitting
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure a leak-free connection.
Grounding System
1 Ground Strap Bolt
M6 x 1.0
1
Ground Strap Bolt
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on similar components. Ensure proper electrical grounding.
Fuse Box System
1 Fuse Box Mounting Bolt
M6 x 1.0
1
Fuse Box Mounting Bolt
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on similar components. Ensure secure mounting.
Ecu System
1 ECU Mounting Bolt
M6 x 1.0
1
ECU Mounting Bolt
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on similar components. Ensure secure mounting.
Wiring Harness System
1 Wiring Harness Clamp Bolt
M6 x 1.0
1
Wiring Harness Clamp Bolt
M6 x 1.0
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Estimated value based on similar components. Prevent damage to the wiring.
Eps System
1 EPS Motor Mounting Bolt
M8 x 1.25
1
EPS Motor Mounting Bolt
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Estimated value based on similar components. Ensure secure mounting.
Emissions Sensors
Torque specifications for Emissions_sensors
Emissions Sensors
Torque specifications for Emissions_sensors
Exhaust Manifold Sensors
1 Oxygen Sensor (Upstream)
M18 x 1.5
1
Oxygen Sensor (Upstream)
M18 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the sensor is properly aligned before tightening. Do not overtighten.
2 Exhaust Temperature Sensor
M10 x 1.25
2
Exhaust Temperature Sensor
M10 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated torque value based on similar M10 bolts. Ensure proper grounding of the sensor.
Catalytic Converter Sensors
1 Downstream Oxygen Sensor
M18 x 1.5
1
Downstream Oxygen Sensor
M18 x 1.5
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the sensor is properly aligned before tightening. Do not overtighten.
2 NOx Sensor
M12 x 1.25
2
NOx Sensor
M12 x 1.25
Torque Specification
22 ft-lbs (30 N·m)
Important Notes
Estimated torque value based on similar M12 bolts. Ensure proper electrical connections.
Egr System Sensors
1 EGR Valve Position Sensor
M6 x 1.0
1
EGR Valve Position Sensor
M6 x 1.0
Torque Specification
7 ft-lbs (9.5 N·m)
Important Notes
Ensure the sensor is properly aligned with the EGR valve shaft.
2 EGR Temperature Sensor
M8 x 1.25
2
EGR Temperature Sensor
M8 x 1.25
Torque Specification
12 ft-lbs (16 N·m)
Important Notes
Estimated torque value based on similar M8 bolts. Ensure proper grounding of the sensor.
Exhaust
Torque specifications for Exhaust
Exhaust
Torque specifications for Exhaust
Exhaust Manifold Headers
1 Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.25
1
Exhaust Manifold/Headers to Cylinder Head Bolts
M10 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Torque values are based on typical M10 bolt specifications. Ensure bolts are tightened in a crisscross pattern to evenly distribute pressure.
2 Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.25
2
Exhaust Pipe to Exhaust Manifold/Headers Bolts
M10 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Torque values are based on typical M10 bolt specifications. Ensure gasket is properly seated before tightening.
Catalytic Converter
1 Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.25
1
Catalytic Converter to Exhaust Pipe Bolts
M10 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Torque values are based on typical M10 bolt specifications. Ensure gasket is properly seated before tightening.
Muffler
1 Muffler to Exhaust Pipe Bolts
M10 x 1.25
1
Muffler to Exhaust Pipe Bolts
M10 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Torque values are based on typical M10 bolt specifications. Ensure gasket is properly seated before tightening.
Exhaust Hangers
1 Exhaust Hanger Bolts
M8 x 1.25
1
Exhaust Hanger Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Torque values are estimated based on typical M8 bolt specifications.
Oxygen Sensor
1 Oxygen Sensor Mounting Bolts
M10 x 1.25
1
Oxygen Sensor Mounting Bolts
M10 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Torque values are based on typical M10 bolt specifications.
Heat Shield
1 Exhaust Heat Shield Bolts
M6 x 1.0
1
Exhaust Heat Shield Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Torque values are estimated based on typical M6 bolt specifications.
Flex Pipe Joints
1 Flex Pipe/Exhaust Joint Bolts
M10 x 1.25
1
Flex Pipe/Exhaust Joint Bolts
M10 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Torque values are based on typical M10 bolt specifications.
Fuel
Torque specifications for Fuel
Fuel
Torque specifications for Fuel
Fuel Delivery System
1 Fuel Rail Bolts
M6 x 1.0
1
Fuel Rail Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensures a leak-free connection and prevents fuel pressure loss.
2 Fuel Injector Bolts
M6 x 1.0
2
Fuel Injector Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensures a proper seal and prevents fuel leaks or injector misalignment.
3 High-Pressure Fuel Line Fittings
M8 x 1.25
3
High-Pressure Fuel Line Fittings
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensures a secure connection and prevents fuel leaks under high pressure.
4 Fuel Pressure Regulator Bolts
M6 x 1.0
4
Fuel Pressure Regulator Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensures consistent fuel pressure and prevents leaks.
Fuel Storage System
1 Fuel Pump Mounting Bolts
M8 x 1.25
1
Fuel Pump Mounting Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensures the pump is securely mounted and prevents fuel leaks or pump failure.
2 Fuel Tank Strap Bolts
M8 x 1.25
2
Fuel Tank Strap Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensures the tank is held securely and prevents movement or fuel leaks.
3 Fuel Tank Sender Unit Bolts
M6 x 1.0
3
Fuel Tank Sender Unit Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensures accurate fuel level readings and prevents fuel leaks.
Fuel Filling System
1 Fuel Filler Neck Bolts
M6 x 1.0
1
Fuel Filler Neck Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensures a tight seal and prevents fuel vapor leaks.
2 Fuel Line Clamp Bolts
M5 x 0.8
2
Fuel Line Clamp Bolts
M5 x 0.8
Torque Specification
6 ft-lbs (8 N·m)
Important Notes
Prevents fuel line movement and potential abrasion or leaks.
Fuel Filtration System
1 Fuel Filter Bolt/Nut
M8 x 1.25
1
Fuel Filter Bolt/Nut
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensures a leak-free connection and maintains fuel system pressure.
Hvac
Torque specifications for Hvac
Hvac
Torque specifications for Hvac
Ac Compressor
1 A/C Compressor Mounting Bolts
M8 x 1.25
1
A/C Compressor Mounting Bolts
M8 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to evenly distribute load.
Ac Lines
1 A/C Line Fittings
M10 x 1.5
1
A/C Line Fittings
M10 x 1.5
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Use a backup wrench to prevent twisting of the A/C lines during tightening.
Cooling System
1 Thermostat Housing Bolts
M6 x 1.0
1
Thermostat Housing Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Ensure the housing gasket is properly seated before tightening.
2 Water Pump Bolts
M8 x 1.25
2
Water Pump Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the water pump gasket is properly seated before tightening.
Heater Core
1 Heater Core Mounting Bolts
M6 x 1.0
1
Heater Core Mounting Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on similar components. Ensure bolts are tightened evenly to avoid warping the heater core.
2 Heater Core Inlet/Outlet Pipe Bolts
M8 x 1.25
2
Heater Core Inlet/Outlet Pipe Bolts
M8 x 1.25
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Estimated value based on similar components. Use a backup wrench to prevent twisting of the pipes.
Blower Motor
1 Blower Motor Mounting Bolts
M6 x 1.0
1
Blower Motor Mounting Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on similar components. Ensure bolts are tightened evenly to avoid misalignment.
Evaporator Core
1 Evaporator Core Mounting Bolts
M6 x 1.0
1
Evaporator Core Mounting Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on similar components. Ensure bolts are tightened evenly to avoid warping the evaporator core.
Hvac Case
1 HVAC Case/Assembly Bolts
M6 x 1.0
1
HVAC Case/Assembly Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on similar components. Ensure bolts are tightened evenly to avoid warping the case.
Blend Door Actuator
1 Blend Door Actuator Bolts
M6 x 1.0
1
Blend Door Actuator Bolts
M6 x 1.0
Torque Specification
8 ft-lbs (11 N·m)
Important Notes
Estimated value based on similar components. Ensure bolts are tightened evenly to avoid misalignment.
Suspension
Torque specifications for Suspension
Suspension
Torque specifications for Suspension
Strut Shock Absorber
1 Strut/Shock Absorber Mounting Bolts
M12 x 1.5
1
Strut/Shock Absorber Mounting Bolts
M12 x 1.5
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Torque value is an average of the provided range (45-55 ft-lbs).
2 Lower Strut Mounting Bolts
M12 x 1.5
2
Lower Strut Mounting Bolts
M12 x 1.5
Torque Specification
55 ft-lbs (75 N·m)
Important Notes
Torque value is an average of the provided range (50-60 ft-lbs).
3 Upper Strut Mounting Bolts
M10 x 1.25
3
Upper Strut Mounting Bolts
M10 x 1.25
Torque Specification
30 ft-lbs (41 N·m)
Important Notes
Torque value is an average of the provided range (25-35 ft-lbs).
Control Arm Ball Joint
1 Control Arm Bolts
M14 x 1.5
1
Control Arm Bolts
M14 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Torque value is an average of the provided range (55-65 ft-lbs).
2 Ball Joint Nut
M12 x 1.5
2
Ball Joint Nut
M12 x 1.5
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Torque value is an average of the provided range (55-65 ft-lbs).
Steering Components
1 Tie Rod End Nut
M10 x 1.25
1
Tie Rod End Nut
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Torque value is an average of the provided range (35-45 ft-lbs).
2 Steering Gear/Rack Bolts
M14 x 1.5
2
Steering Gear/Rack Bolts
M14 x 1.5
Torque Specification
70 ft-lbs (95 N·m)
Important Notes
Torque value is an average of the provided range (65-75 ft-lbs).
Sway Bar
1 Sway Bar Link Nut
M10 x 1.25
1
Sway Bar Link Nut
M10 x 1.25
Torque Specification
40 ft-lbs (54 N·m)
Important Notes
Torque value is an average of the provided range (35-45 ft-lbs).
2 Sway Bar Bracket Bolts
M8 x 1.25
2
Sway Bar Bracket Bolts
M8 x 1.25
Torque Specification
25 ft-lbs (34 N·m)
Important Notes
Torque value is an average of the provided range (20-30 ft-lbs).
Rear Suspension
1 Rear Suspension Trailing Arm Bolts
M14 x 1.5
1
Rear Suspension Trailing Arm Bolts
M14 x 1.5
Torque Specification
65 ft-lbs (88 N·m)
Important Notes
Torque value is an average of the provided range (60-70 ft-lbs).
2 Rear Shock Absorber Mounting Bolts
M12 x 1.5
2
Rear Shock Absorber Mounting Bolts
M12 x 1.5
Torque Specification
45 ft-lbs (61 N·m)
Important Notes
Torque value is an average of the provided range (40-50 ft-lbs).
Wheels
1 Wheel Lug Nuts
M12 x 1.5
1
Wheel Lug Nuts
M12 x 1.5
Torque Specification
100 ft-lbs (136 N·m)
Important Notes
Torque value is an average of the provided range (95-110 ft-lbs). Always use a star pattern when tightening lug nuts.
Subframe
1 Subframe Mounting Bolts
M16 x 1.5
1
Subframe Mounting Bolts
M16 x 1.5
Torque Specification
80 ft-lbs (108 N·m)
Important Notes
Torque value is an average of the provided range (70-90 ft-lbs). Follow the manufacturer's recommended torque sequence.
Tg 81 Transmission
Torque specifications for Tg 81 Transmission
Tg 81 Transmission
Torque specifications for Tg 81 Transmission
Transmission Mounting
1 Transmission Mounting Bolts
M10 x 1.5
1
Transmission Mounting Bolts
M10 x 1.5
Torque Specification
35 ft-lbs (47 N·m)
Important Notes
Ensure bolts are tightened in a crisscross pattern to maintain even pressure.
2 Transmission Crossmember Bolts
M12 x 1.75
2
Transmission Crossmember Bolts
M12 x 1.75
Torque Specification
50 ft-lbs (68 N·m)
Important Notes
Estimated value based on similar crossmember bolt sizes.
Oil Pan And Plugs
1 Transmission Oil Pan Bolts
M6 x 1.0
1
Transmission Oil Pan Bolts
M6 x 1.0
Torque Specification
10 ft-lbs (14 N·m)
Important Notes
Ensure the oil pan gasket is properly seated before tightening.
2 Transmission Drain Plug
M14 x 1.5
2
Transmission Drain Plug
M14 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Use a new crush washer to ensure a proper seal.
3 Transmission Fill Plug
M14 x 1.5
3
Transmission Fill Plug
M14 x 1.5
Torque Specification
23 ft-lbs (31 N·m)
Important Notes
Use a new crush washer to ensure a proper seal.
Drivetrain Connections
1 Drive Axle/Half Shaft Bolts
M12 x 1.75
1
Drive Axle/Half Shaft Bolts
M12 x 1.75
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure the axle is properly seated before tightening.
2 CV Joint/Axle Nut
M24 x 1.5
2
CV Joint/Axle Nut
M24 x 1.5
Torque Specification
190 ft-lbs (258 N·m)
Important Notes
Use a new cotter pin after torquing the nut.
3 Propeller/Drive Shaft Bolts
M12 x 1.75
3
Propeller/Drive Shaft Bolts
M12 x 1.75
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure the drive shaft is properly aligned before tightening.
Starter Motor
1 Starter Motor Mounting Bolts
M8 x 1.25
1
Starter Motor Mounting Bolts
M8 x 1.25
Torque Specification
33 ft-lbs (45 N·m)
Important Notes
Ensure the starter motor is properly aligned before tightening.
Bellhousing And Torque Converter
1 Transmission Bellhousing Bolts
M12 x 1.75
1
Transmission Bellhousing Bolts
M12 x 1.75
Torque Specification
60 ft-lbs (81 N·m)
Important Notes
Ensure the transmission is properly aligned with the engine block.
2 Torque Converter Bolts
M8 x 1.25
2
Torque Converter Bolts
M8 x 1.25
Torque Specification
28 ft-lbs (38 N·m)
Important Notes
Ensure the torque converter is properly seated before tightening.
Shift Linkage
1 Transmission Shift Linkage Bolts
M6 x 1.0
1
Transmission Shift Linkage Bolts
M6 x 1.0
Torque Specification
18 ft-lbs (24 N·m)
Important Notes
Ensure the shift linkage is properly aligned before tightening.
Cooling System
1 Transmission Cooler Line Fittings
M10 x 1.25
1
Transmission Cooler Line Fittings
M10 x 1.25
Torque Specification
20 ft-lbs (27 N·m)
Important Notes
Ensure the cooler lines are properly seated before tightening.
Troubleshooting Guide
Common issues, diagnostic steps, and prevention guidelines
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Common Issues
Bolt stretching, stripped threads, uneven torque patterns
Loose Components
Symptoms:
- Rattling or vibration noises
- Visible movement in components
- Uneven panel gaps
Solutions:
- Clean threads and mounting surfaces
- Replace damaged fasteners
- Apply proper torque in sequence
- Use thread locker if specified
Stripped Fasteners
Symptoms:
- Unable to achieve proper torque
- Fastener spins freely
- Visible thread damage
Solutions:
- Use thread repair kit if appropriate
- Install thread insert (HeliCoil)
- Replace component if threaded hole is damaged
- Upgrade to higher grade fastener if recommended
Overtightened Components
Symptoms:
- Cracked or deformed parts
- Broken fasteners
- Compressed gaskets or seals
Solutions:
- Replace damaged components
- Use new fasteners
- Follow proper torque sequence
- Verify correct torque specifications
Diagnostic Steps
Visual inspection, torque verification, thread assessment
Diagnostic Steps
Visual inspection, torque verification, thread assessment
1
Visual Inspection
Inspect the affected area for any visible signs of damage or wear
- Check for cracks or deformation
- Look for signs of excessive wear
- Verify proper fastener installation
2
Torque Verification
Verify the torque applied to the fasteners
- Check the torque wrench calibration
- Verify the torque specification
- Compare the applied torque to the specification
3
Thread Assessment
Assess the condition of the threads
- Check for signs of thread damage
- Verify the thread type and size
- Check for proper thread engagement
Prevention Guidelines
Best practices, maintenance tips, tool care
Prevention Guidelines
Best practices, maintenance tips, tool care
Best Practices
- Always follow the recommended torque specification
- Use the correct type and size of fasteners
- Verify the torque wrench calibration regularly
Maintenance Tips
- Regularly inspect the affected area for signs of wear or damage
- Replace damaged or worn-out components promptly
- Keep the work area clean and organized
Tool Care
- Regularly clean and maintain the torque wrench
- Store the torque wrench in a dry and secure location
- Verify the torque wrench calibration before each use
Frequently Asked Questions
Find answers to common questions about torque specifications
Q1 What IS the recommended torque for the wheel lug nuts on a 2017-Present Volvo xc40?
Q1
What IS the recommended torque for the wheel lug nuts on a 2017-Present Volvo xc40?
According to Volvo specifications, the wheel lug nuts must be tightened to 120 Nm (89 lb-ft).
Q2 Can I use a regular torque wrench to tighten engine bolts?
Q2
Can I use a regular torque wrench to tighten engine bolts?
No, a regular torque wrench IS not suitable for tightening engine bolts. Volvo recommends using a calibrated, click-type torque wrench with angle measurement capabilities.
Q3 What IS the tightening sequence for the cylinder head bolts on a Volvo xc40?
Q3
What IS the tightening sequence for the cylinder head bolts on a Volvo xc40?
Refer to Volvo VIDA software or a Volvo certified technician for the specific tightening sequence and torque values for cylinder head bolts.
Q4 What are some common torque mistakes to avoid when working on a Volvo xc40?
Q4
What are some common torque mistakes to avoid when working on a Volvo xc40?
Overtightening bolts, using the wrong torque settings, and failing to follow the correct tightening sequence can lead to component damage and safety hazards.
Q5 How can I ensure the accuracy of my torque wrench?
Q5
How can I ensure the accuracy of my torque wrench?
Regularly calibrate your torque wrench according to the manufacturer's instructions. A professional calibration service IS also recommended periodically.
Q6 Where can I find additional technical information about torque specifications for my Volvo xc40?
Q6
Where can I find additional technical information about torque specifications for my Volvo xc40?
Consult the Volvo VIDA workshop software, Volvo technical bulletins, or refer to a certified Volvo technician.
Environmental Considerations
Temperature, humidity, and seasonal effects on torque specifications
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature Effects
Includes: High Heat, Cold Weather, Thermal Cycling
Temperature can significantly impact torque values and fastener behavior
Cold Weather
Effects:
- Increased material brittleness
- Higher torque required due to thread contraction
- Reduced thread lubricant effectiveness
Recommendations:
- Allow components to warm to room temperature when possible
- Consider using winter-grade thread lubricants
- Check torque values more frequently during winter months
Hot Weather
Effects:
- Thermal expansion of components
- Decreased friction in threads
- Accelerated lubricant breakdown
Recommendations:
- Check torque when components are at normal operating temperature
- Use temperature-resistant thread lockers
- Consider re-torquing after heat cycles
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Humidity and Corrosion
Covers: Rust Prevention, Salt Exposure, Moisture Control
Moisture and corrosion can affect fastener integrity and torque values
High Humidity
Effects:
- Accelerated corrosion formation
- Reduced friction coefficient
- Potential thread seizing
Prevention:
- Use corrosion-resistant fasteners
- Apply appropriate anti-seize compounds
- Maintain proper protective coatings
Salt Exposure
Effects:
- Rapid corrosion development
- Thread damage
- Seized fasteners
Prevention:
- Regular underbody washing
- Use of sacrificial anodes where appropriate
- Application of protective coatings
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Seasonal Maintenance
Spring, Summer, Fall, and Winter maintenance schedules
Spring
- Inspect for winter damage
- Clean and protect exposed fasteners
- Check torque on critical components
Summer
- Monitor heat-affected components
- Check expansion-related loosening
- Inspect cooling system mounts
Fall
- Prepare for winter conditions
- Apply corrosion protection
- Verify all fasteners are properly torqued
Winter
- More frequent inspection of critical fasteners
- Check for salt damage
- Monitor suspension component torque
Related Resources
Tools, service procedures, and technical bulletins
Recommended Tools
Digital Torque Wrench (10-100 Nm)
Essential for tightening fasteners to precise torque specifications, preventing damage and ensuring proper assembly. This range IS suitable for many applications on the XC40.
- Digital display for accurate readings
- Audible alarm when target torque IS reached
- Multiple units (Nm, ft-lb, in-lb)
- Reversible ratcheting mechanism
Service Procedures
Technical Service Bulletins
Legal Disclaimer
Important information about using this content
Always refer to your vehicle's service manual and take appropriate safety precautions when performing any maintenance or repairs.
General Information
The information provided on this website is for general informational purposes only. While we strive to maintain accuracy in our content, all specifications, procedures, and technical information should be verified against your vehicle's official service manual or with the manufacturer directly.
Warranty & Liability
The content on this website is provided "as is" without any representations or warranties, express or implied. We make no representations or warranties regarding the accuracy, completeness, or availability of the information.
We shall not be liable for any direct, indirect, special, or consequential damages arising from the use of information on this website.
Technical Information
- All specifications, including torque values, fluid capacities, and maintenance procedures, should be verified against your vehicle's factory service manual.
- Vehicle specifications and procedures may vary by model year, trim level, and region.
- Always follow the manufacturer's recommended procedures and safety precautions.
- Working on vehicles can be dangerous. Always take proper safety precautions and use appropriate safety equipment.
- If you're unsure about any procedure, consult a qualified professional mechanic.
Intellectual Property
All content, including text, images, and specifications, is protected by copyright and other intellectual property laws. Any unauthorized use or reproduction is prohibited.
About the Author
Expert automotive knowledge and experience
'/%3E%3Cpath d='M60 30a20 20 0 1 1 0 40 20 20 0 0 1 0-40zm0 45c16.5 0 30 7.5 30 16.8V100H30v-8.2c0-9.3 13.5-16.8 30-16.8z' fill='%23404040'/%3E%3C/svg%3E)
ASE
15+ Years
Experience
500+ Guides
Guides
50+ Makes
Vehicles
1000+ Solutions
Solutions
Diagnostic
Specialized in advanced diagnostic techniques using modern scan tools and oscilloscopes.
Repair
Expert in both traditional mechanical repairs and modern vehicle systems.
Additional Expertise
Documentation
Created over 500 detailed repair guides and technical documents.
Training
Conducted technical training sessions and contributed to repair databases.
Certifications & Research
Certifications
- ASE Master Technician Certification
- Advanced Diagnostic Specialist
- Hybrid/Electric Vehicle Systems
- Performance Tuning Expert
Research & Community
Actively researches emerging technologies and contributes to automotive forums.